Exterior Projection 1000 Outdoor-Rated Large Scale Image Projector (US)

FEATURES:
Flat field, high contrast image projection based on high power LED engine
0-100% electronic dimming
Full CMY color mixing + additional color wheel with 7 interchangeable colors
7 gobo slots for projecting graphic images (gobos included)
Animation system for creating animated lighting effects (horizontal and vertical)
Zoom range from 10° - 44° for exact projection on desired surface
Variable frost for creating morphing effects and hybrid function as wash light
2 rotating prisms for creating abstract multi patterns
Intuitive setup, configuration and stand-alone programming via graphical OLED display
RDM and DMX control
Fully weatherized IP66 fixture for permanent outdoor installation
Fully convection cooling using heat pipes technology

SPECIFICATIONS:
PHYSICAL
Length: 702 mm (27.7 in.)
Width: 417 mm (16.5 in.)
Height: 618 mm (24.4 in.)
Weight: 50 kg (110 lb.)

All figures include mounting yoke

DYNAMIC EFFECTS
Color mixing: CMY, independently variable 0 - 100%
Color wheel: 7 interchangeable colors + open
Gobo wheel: 7 rotating gobos plus open, indexing, variable rotation
Gobo animation wheel: Indexing, continuous rotation with variable angle, speed and direction
Zoom: 10° - 44° (cutoff angles)
Prism: Prism wheel with 2 interchangeable prisms, prism rotation and indexing
Frost filter: Motorized, variable
Dimming: Electronic, constantly variable 0-100%, 16-bit control
Shutter: Electronic, strobe and pulse effects, instant open and blackout
Focus: Motorized, variable 3 m (9.8 ft.) to infinity

CONTROL AND PROGRAMMING
Control options: DMX, RDM, standalone
Stand-alone control: Up to 20 scenes with global fade/hold times
Configuration, addressing and status: Onboard control panel with OLED display or via RDM
8-bit control: CMY, color selection, gobo selection, prism, frost, animation
16-bit control: Gobo indexing and rotation, zoom, focus and intensity
DMX channels: 20
DMX compliance: USITT DMX512-A
RDM compliance: ANSI/ESTA E1.20

OPTICS
Light source: 440 W white light LED engine
CRI (Color Rendering Index): 72
Color temperature: 6500 K (±250 K)
LED lifetime: 20, 000 hours (to >70% luminous output)*
LED manufacturer: Appotronics

*Figure obtained under manufacturer's test conditions

PHOTOMETRIC DATA
Cutoff angle: 10° - 44°

Luminous intensity:
At 10° zoom: 11, 500 lumens
At 16° zoom: 15, 000 lumens
At 40° zoom: 16, 800 lumens

Center Peak:
At 10° zoom: 731, 000 cd
At 16° zoom: 311, 000 cd
At 40° zoom: 42, 000 cd

CONSTRUCTION
Housing: Cast aluminum
Finish: Hard anodized, white or metallic gray lacquered
Front glass: 5 mm (0.2 in.) anti-reflection coated tempered glass
Ingress protection: IP66
Impact resistance: IK08 (with control panel display cover plate installed)
Corrosion resistance: C5-M (very high corrosivity / marine, ISO 12944)
Vibration resistance: 1.0g, Sinusoidal (IEC 60068-2-6)
0, 7g RMS Random (IEC 60068-2-64)
EPA (Effective Projected Area): 0.28m²

GOBOS
Suitable material: Metal or borosilicate glass, coatings heat-resistant to 450°C (842° F)
Gobo diameter: 30.0 mm +0/-0.3 mm (1.2 in. +0/-0.02 in.)
Maximum image diameter: 26 mm (1.02 in.)
Gobo thickness, minimum: 1.1 mm ±0.1 mm (0.045 ±0.004 in.)
Gobo thickness, maximum: 3.0 mm ±0.3 mm (0.118 in. ± 0.012 in.)*

*Gobos thicker than 2.5 mm require a shorter spring in the gobo holder

INSTALLATION
Mounting: Adjustable yoke
Location: Suitable for wet locations. Do not immerse in water.
Orientation: Any (sides must be kept vertical)
Minimum distance to illuminated surfaces: 0.5 m (20 in.)

CONNECTIONS
Power cable entry: IP66 cable gland
Power connection: 1.8 m (5.9 ft.) cable tail with bare ends
Power cable type: EU models: H07RN-F 450/700V, Ø10 mm
US models: SJTW 14 AWG, 300V, Ø9.3 mm
Data cable entry: IP66 cable gland
Data connection: 1.8 m (5.9 ft.) combined input + output cable tail with bare ends

ELECTRICAL
AC power: 100-120/200-277 V nominal, 50/60 Hz
Power Supply: Auto-ranging electronic switch-mode
Typical half-cycle RMS inrush current: 15.5 A
Idle power (zero intensity, no effects applied): 75 W
Surge protection: 4 KV

TYPICAL POWER AND CURRENT
120 V, 60 Hz: 645 W, 5.5 A, PF 0.98
230 V, 50 Hz: 635 W, 2.9 A, PF 0.95
277 V, 60 Hz: 635 W, 2.6 A, PF 0.90

Figures are typical, not maximum. Measurements made at nominal voltage with all LEDs at full intensity. Allow for a deviation of +/- 10%.

THERMAL
Cooling: Convection, internal forced air
Total heat dissipation (calculated): 2350 BTU/hr.
Maximum surface temperature: 85° C (185 ° F)
Maximum ambient temperature (Ta max.): 45° C (113° F)*
Minimum ambient temperature (Ta min.): -30° C (-22° F)**

*Above this temperature, the fixture regulates output to protect from overheating.

**For instant wake-up with no warm-up mode, leave power applied constantly in ambient temperatures below 0° C (32° F).

APPROVALS
EU safety: EN 60598-2-1, EN 60598-2-5 (EN 60598-1), EN 62471, EN 62493
EU EMC: EN 55015, EN 55032, EN 55103-2, EN 61000-3-2, EN 61000-3-3, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61547
US safety: ANSI/UL 1598
US EMC: CFR 47 Part 15 Class A
Canadian safety: CSA C22.2 No 250.0
Australia/NZ: RCM
Global CB Certification/IECEE: IEC 60598-2-5 (IEC 60598-1)

INCLUDED ITEMS
Silica gel desiccant bag: P/N 37220000
Two gobo retaining springs

ACCESSORIES
Glare Shield, Exterior Projection 1000: P/N 91611768
Projection Setup Gobo, Exterior Projection 1000: P/N 91616075
Ring for gobo, OD30, set of 10 pcs: P/N MAR-91611851

RELATED ITEMS
Martin RDM 5.5 Splitter: P/N 90758150
Martin Companion Cable: P/N 91616091
Martin Companion Software Suite (including firmware uploader)

SPARE PARTS
Silica gel desiccant bag in sealed foil pack: P/N 37220000
Gobo holder for EP1000 with magnet incl. washer & short spring: P/N 50482185
Gobo holder for EP1000 with magnet incl. washer & long spring: P/N 50482186

ORDERING INFORMATION
Exterior Projection 1000, US, Aluminum: P/N 90512005