Exterior Projection 500 Outdoor-Rated Medium Scale Image Projector (US)

FEATURES:
Up to 6100 lumens output with 4 beam angles variants from narrow to wide
Powerful close-range and long-range projection
Flat-field, high-contrast image projection based on high-power LED engine
4 layers of versatile dynamic effects (colors, gobo projection, gobo animation, prisms/frost)
Crisp image projection
Rugged IP66-rated housing
Minimal maintenance – low total cost of ownership

SPECIFICATIONS:
PHYSICAL
Length: 415 mm (16.4 in.)
Width: 293 mm (11.6 in.)
Height: 444 mm (17.5 in.)
Weight: 17.5 kg (38.6 lb.)

All figures include mounting yoke

DYNAMIC EFFECTS
Color wheel: 8 interchangeable colors + open
Gobo wheel: 6 rotating gobos plus open, indexing, variable rotation
Gobo animation: Variable speed linear animation effect
Prism: Prism wheel with 2 interchangeable prisms, prism rotation and indexing
Frost (wash effect): Motorized variable
Dimming: Electronic, constantly variable 0-100%, 16-bit control
Shutter: Strobe and pulse effects, instant open and blackout
Focus: Motorized, variable 3 m (9.8 ft.) to infinity

CONTROL AND PROGRAMMING
Control options: DMX, RDM, standalone
Control resolution: 8-bit DMX control of each color
Configuration, addressing and status: Onboard control panel with OLED display
DMX channels: 13
DMX compliance: USITT DMX512-A
RDM compliance: ANSI/ESTA E1.20

OPTICS
Light source: 230 W white light LED engine
CRI (Color Rendering Index): 72
Color temperature: 8300 K
LED lifetime: 20, 000 hours (to >70% luminous output)*
LED manufacturer: Prolight Opto

*Figure obtained under manufacturer's test conditions

PHOTOMETRIC DATA
Narrow:
Cutoff angle: 12°
Total output: 5000 lumens
Center peak: 203, 000 cd

Medium:
Cutoff angle: 22°
Total output: 6100 lumens
Center peak: 77, 000 cd

Wide:
Cutoff angle: 37°
Total output: 5700 lumens
Center peak: 28, 000 cd

Very Wide:
Cutoff angle: 50°
Total output: 3400 lumens
Center peak: 11, 000 cd

CONSTRUCTION
Housing: Cast aluminum
Finish: Hard anodized, metallic gray lacquered
Front glass: 5 mm (0.2 in.) anti-reflection coated tempered glass
Ingress protection: IP66
Impact resistance: IK08 (with control panel display cover plate installed)
Corrosion resistance: C5-M (very high corrosivity / marine, ISO 12944)
Vibration resistance: 1.0g, Sinusoidal (IEC 60068-2-6)
0, 7g RMS Random (IEC 60068-2-64)
EPA (Effective Projected Area): 0.15 m2
RoHS compliant

GOBOS
Suitable material: Borosilicate glass, coatings heat-resistant to 450°C (842° F)
Alternative material: Aluminum 1060, paint on front lens side, 450° C (842° F)
Gobo diameter: 30.0 mm +0/-0.3 mm (1.2 in. +0/-0.02 in.)
Maximum image diameter: 23 mm (0.91 in.)
Glass gobo thickness, minimum: 1.1 mm ±0.1 mm (0.045 ±0.004 in.)
Glass gobo thickness, maximum: 3.0 mm ±0.3 mm (0.12 in. ± 0.012 in.)
Aluminum gobo thickness: 0.5 mm ± 0.02 mm (0.020 in. ± 001 in.)
HT paint

INSTALLATION
Mounting: Adjustable yoke
Location: Suitable for wet locations. Do not immerse in water.
Orientation: Any (sides must be kept vertical)
Minimum distance to illuminated surfaces: 0.5 m (20 in.)

CONNECTIONS
Power cable entry: IP68 cable gland
Power connection: 1.8 m (5.9 ft.) cable tail with bare ends
Data cable entry: IP68 cable gland
Data connection: 1.8 m (5.9 ft.) combined input + output cable tail with bare ends

ELECTRICAL
AC power: 100-240/277 V nominal, 50/60 Hz
Power Supply: Auto-ranging electronic switch-mode
Typical half-cycle RMS inrush current: 8.4 A
Idle power (zero intensity, no effects applied): 32 W, 0.3 A
Surge protection: 4 KV

TYPICAL POWER AND CURRENT
110 V, 60 Hz: 320 W, 2.9 A, PF 0.977
230 V, 50 Hz: 310 W, 1.4 A, PF 0.971
277 V, 60 Hz: 305 W, 1.2 A, PF 0.950

Figures are typical, not maximum. Measurements made at nominal voltage with all LEDs at full intensity. Allow for a deviation of +/- 10%.

THERMAL
Cooling: Convection, internal forced air
Total heat dissipation (calculated): 1100 BTU/hr.
Maximum surface temperature: 85° C (185° F)
Maximum ambient temperature (Ta max.): 45° C (113° F) *
Minimum ambient temperature (Ta min.): -30° C (-22° F)**

*Above this temperature, the fixture regulates output to protect from overheating.
**For instant wake-up with no warm-up mode, leave power applied constantly in ambient temperatures below 0° C (32° F)

APPROVALS
EU safety: EN 60598-2-1, EN 60598-2-5 (EN 60598-1), EN 62471, EN 62493
EU EMC: EN 55015, EN 55032, EN 55103-2, EN 61000-3-2, EN 61000-3-3, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61547
US safety: ANSI/UL 1598
US EMC: CFR 47 Part 15 Class A
Canadian safety: CSA C22.2 No 250.0
Australia/NZ: RCM
Global CB Certification/IECEE: IEC 60598-2-5 (IEC 60598-1)

ACCESSORIES
Glare Shield, Exterior Projection 500, aluminum: P/N 91611767
Projection Setup Gobo: P/N 91616068
EP-500, Manual Framing Module: P/N 91611842
Ring for gobo, OD30, set of 10 pcs: P/N MAR-91611851

RELATED ITEMS
Martin RDM 5.5 Splitter: P/N 90758150
Martin Companion Cable: P/N 91616091
Martin Companion Software Suite (including firmware uploader)

SPARE PARTS
Silica gel desiccant bag in sealed foil pack: P/N 37220000
Gobo holder with magnet incl. washer, short spring & long spring: P/N 50481990
Gobo holder without magnet incl. washer, short spring & long spring: P/N 50481992

ORDERING INFORMATION
Exterior Projection 500, Medium, US, Aluminum: P/N 90506520