P3 PowerPort 1000 IP Outdoor Power and Data Unit for Martin Creative LED (Installation Model)

FEATURES:
P3 image processing technology
Setup and addressing via P3 System Controller family
No local configuration needed
P3 input and thru to allow daisy-chaining
Optional fiber-interface
4 hybrid power/data output ports
Wall-mountable or freestanding
Can be located up to 50 m away from the creative LED video products
IP66

SPECIFICATIONS:
PHYSICAL
Length: 426 mm (16.8 in.)
Width: 483 mm (19.1 in.)
Height: 146 mm (5.8 in.)
Weight: 8 kg (17.7 lb.)

CONTROL AND PROGRAMMING
Addressing and status: Via P3 System Controller
Mapping: Via P3 System Controller
Firmware update: Via P3 System Controller

CONTROL/USER INTERFACE
Device status: Multicolor status LED
Power output status: Four LEDs
Data output status: Four LEDs
Device test and reset: Pushbutton to call up local test patterns and reset device
Status LEDs and pushbutton can be disabled remotely if required.

P3 SIGNAL PROTOCOL
Signal type: Gigabit Ethernet
Protocol: Proprietary Martin P3
Hot pluggable: Yes, electrically isolated at all connections
Cable type: Ethernet, CAT 5e or better
Cable length: Up to 100 m (328 ft.) between any 2 devices, extendable with Ethernet switch or conversion to fiber

SYSTEM INTEGRATION

VC-Dot family via VC-Feeder
Exterior PixLine family
VDO Sceptron family
VC-Grid family (indoor product)
VC-Strip family (indoor product)
Exterior Dot-HP family

CONSTRUCTION
Housing: Aluminum
Color: Aluminum gray (customized colors available on project basis)
Protection rating: IP66
NEMA enclosure rating: Type 3
Effective Projected Area (EPA): 0.21 m2
RoHS compliant

INSTALLATION
Mounting: Brackets for installation on flat surface
Orientation: Any, except with cable glands facing up or lid facing down

CONNECTIONS
Power input: Cable gland (M20), internal screw terminals
P3 data in/out: Two cable glands (M16), two internal RJ45 connectors (if copper-to-fiber unit is installed, one cable gland can be used for fiber)
M16 cable glands accept 5.5 - 10 mm cable, M20 glands accept 8-13 mm cable.
Combined power & data out: Four cable glands (M16), internal screw terminals

ELECTRICAL
AC power: 120-277 V nominal, 50/60 Hz
Power supply unit: Auto-ranging electronic switch-mode
Typical total power consumption: 1000 W (including full load of connected display devices, all at full intensity)
Typical half-cycle RMS inrush current: 20.9 A
Total power consumption in idle state (at 25° C, all connected devices powered off): 22 W

THERMAL
Cooling: Convection
Maximum ambient temperature (Ta max.): 55° C
Minimum ambient temperature (Ta min.): -30° C
Total heat dissipation (calculated, +/- 10%): 345 BTU/hr. (not including display devices but with system at full load)

APPROVALS
EU safety: EN 60950
EU EMC: EN 55032, EN 55103-2, EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3
US safety: ANSI/UL 60950-1
Canadian safety: CSA C22.2 No. 60950-1

INCLUDED ITEMS
Cable glands

RELATED ITEMS
Martin P3-PC System Controller: Free download from martin.com
P3-050 System Controller: P/N 90721090
P3-100 System Controller: P/N 90721010
P3-150 System Controller: P/N 90721015
P3-200 System Controller: P/N 90721020
P3-300 System Controller: P/N 90721060

ORDERING INFORMATION
Martin P3 PowerPort 1000 IP, Installation Model: P/N 90721080