Power Distribution System with Remote Control Capability and 3-Sequences, RX Surge Protection (15 Amps)
$679.00
Ships Directly from Manufacturer. Contact Us for Availability.
SKU
SP102838
The CQ 1515-RX combines reliable AC power sequencing with the proven performance of the Juice Goose RX Series surge protection and filtration.
Each CQ Series product contains the circuitry needed for sequenced activation and plug-and-play coordination with other CQ Series models or RC Series accessories. All power up and power down sequences are performed automatically. Commands are passed from one CQ Series unit to the next.
The CQ 1515-RX is a single space rack mount device featuring 7 AC power outputs on the rear of the chassis with a combined rating of 15 amps. One output is unswitched. The remaining 6 outputs are grouped into 3 Power Pods of two outputs each. Each Power Pod is an individual sequence event. All outputs have premium, RX Series surge protection and line noise filtration.
Because the CQ 1515-RX is a self contained sequencing circuit, it can be the master or slave in a power sequencing system. Eight wire RJ-45 cable can be connected to this unit's Signal Input and/or Signal Output connectors to link it's operations with other CQ or control devices.
This product features LEDs on the front of the chassis for real time monitoring of the sequencing functions. Individual LEDs light when power is applied to its power pod.
Proven Power Protection
Published test results prove the effectiveness of the power protection circuitry contained in the CQ 1515-RX and other RX Series based products.
This RX power protection technology is particularly valuable because it works against common mode as well as normal mode events. While it protects against dramatic surge events of up to 6,000 volts at 3,000 amps on hot and neutral (normal mode), it also limits ground line (common mode) surges to one-half (0.50) volt to prevent operating faults of digital processing equipment.
Power protection circuitry in the CQ 1515-RX includes a differential transformer, lots of filtering capacitance and control circuitry providing protection from dangerous surges, high frequency interference, building wiring faults and over voltage. RX technology is proven to deliver protection comparable to an isolation transformer. Click here to see RX Series test results.
Each CQ Series product contains the circuitry needed for sequenced activation and plug-and-play coordination with other CQ Series models or RC Series accessories. All power up and power down sequences are performed automatically. Commands are passed from one CQ Series unit to the next.
The CQ 1515-RX is a single space rack mount device featuring 7 AC power outputs on the rear of the chassis with a combined rating of 15 amps. One output is unswitched. The remaining 6 outputs are grouped into 3 Power Pods of two outputs each. Each Power Pod is an individual sequence event. All outputs have premium, RX Series surge protection and line noise filtration.
Because the CQ 1515-RX is a self contained sequencing circuit, it can be the master or slave in a power sequencing system. Eight wire RJ-45 cable can be connected to this unit's Signal Input and/or Signal Output connectors to link it's operations with other CQ or control devices.
This product features LEDs on the front of the chassis for real time monitoring of the sequencing functions. Individual LEDs light when power is applied to its power pod.
Proven Power Protection
Published test results prove the effectiveness of the power protection circuitry contained in the CQ 1515-RX and other RX Series based products.
This RX power protection technology is particularly valuable because it works against common mode as well as normal mode events. While it protects against dramatic surge events of up to 6,000 volts at 3,000 amps on hot and neutral (normal mode), it also limits ground line (common mode) surges to one-half (0.50) volt to prevent operating faults of digital processing equipment.
Power protection circuitry in the CQ 1515-RX includes a differential transformer, lots of filtering capacitance and control circuitry providing protection from dangerous surges, high frequency interference, building wiring faults and over voltage. RX technology is proven to deliver protection comparable to an isolation transformer. Click here to see RX Series test results.
GENERAL DESCRIPTION
The Juice Goose CQ-1515 and 1520, along with the other products in the CQ Series, provide a convenient and economical means of remotely activating AC power in a sequenced array for application to both sensitive and high amperage equipment. CQ Series products need no additional controllers or programming. Each contains the circuitry to be activated by a Juice Goose RC Series accessory or a simple contact closure and to perform in coordination with other CQ devices. All power down sequences are automatically exact reversals of the power up sequences.
OPERATION
The CQ-1515 (15 amp) and CQ-1520 (20 amp) are rack mount, plug-in models featuring AC line protection and seven power outputs. These three sequence event devices can be used by themselves, activated via remote control or included with a more extensive power sequencing system. In a typical sequencing system the rack mounted CQ is used to control power to the signal source or “front-of-house” equipment before power is applied to amplifiers. In this configuration, the initial CQ in the series is connected by way of eight wire modular phone cable to another CQ device at that or another location. No time delay settings or additional equipment are required. All CQ units will automatically turn on and off in the proper sequence. Note: the CQ-1520 has a 20 amp capacity and requires a NEMA 5/20R AC receptacle for connection of the power cord to the main AC power.
The CQ-1515 and CQ-1520 feature three sequenced duplex receptacles and one unswitched single AC receptacle on the back of the chassis. Each duplex has its own preset turn on and off timing. Because the CQ activates its outlets in three stages it is useful as a stand-alone sequencer. Signal source and processing equipment can be powered by the first sequence stages while amplifiers are powered by the last ones. The CQ can be triggered by the switch on the front of the unit, by a remote contact closure or by a Juice Goose RC5 accessory.
CONTROL LINE CONNECTION
All CQ products can be easily controlled by way of 8 wire, RJ-45 cable. (Consult the CQ Series Owners Manual before assembling the cable.) Each CQ has a Sequence Signal Input and Output connector on the chassis. This communication link allows any CQ device to be installed at any stage in a power sequencing system. Sequence timing is controlled by a nominal 8 VDC “Outputs Active” circuit between the units which is regenerated with each CQ module. There is no limit to the number of CQ devices that can be connected and no practical distance limit between them.
The system can be activated with the sequence control switch on the CQ device itself or a Juice Goose RC5 control accessory. The sequence process can also be initiated with a latching contact closure, enabling use of a custom mounted single pole switch, a relay or processor based controllers from Crestron, AMX or other manufacturers.
CONTROLS AND MONITORS
The CQ-1515 and CQ-1520 feature a two position switch on the front of the chassis. This switch is active only if there is no control cable on the Sequence Signal Input connector. When active, this switch causes the unit to turn outlets on or off in sequence and to control the sequencing of any unit connected to the Sequence Signal Output connector. A Manual Override switch allows the CQ to be manually operated, overriding the control circuit in the unlikely event of a fault or failure.
Lights on the front of the chassis allow monitoring of the unit operation. The Processor light will blink to indicate the control processor on the unit is functioning. The POD lights are illuminated as a result of contact closure by the CQ relays, indicating that actual relay closure has occurred.
POWER PROTECTION
The CQ-1515 and CQ-1520 feature a multistage AC line filter to reduce high frequency interference and a triple surge protection matrix across hot, neutral and ground power leads.
DETAIL SPECIFICATIONS
Chassis: Tour Class 16 gauge steel with 11 gauge rack mount brackets
Dimensions: 1.75”H x19”W x 7”D
Weight: 10 lb.
Circuit Breaker (thermal on back of the chassis): CQ-1515 15A: CQ-1520 20A
AC Power Filtration: Multistage Filter (48 DB @ 30 MHz)
AC Surge Protection: Triple surge protection matrix on hot, neutral and ground
Number of Sequence Events: Three Power Input (seven foot power cord): CQ-1515 14/3 SJ with NEMA 5/15P plug, CQ-1520 12/3 SJ with 5/20P (requires a 5/20R receptacle)
Power Output (plus one unswitched NEMA 5/15R on back of the chassis), CQ-1515 six sequenced NEMA 5/15R, CQ-1520 six sequenced NEMA 5/20R
Input Voltage: US standard (120 VAC @ 60 Hz)
Signal Connections: RJ-45, eight wire cable
Monitor Features: Monitor LEDs correlate to processor and relay operation
The Juice Goose CQ-1515 and 1520, along with the other products in the CQ Series, provide a convenient and economical means of remotely activating AC power in a sequenced array for application to both sensitive and high amperage equipment. CQ Series products need no additional controllers or programming. Each contains the circuitry to be activated by a Juice Goose RC Series accessory or a simple contact closure and to perform in coordination with other CQ devices. All power down sequences are automatically exact reversals of the power up sequences.
OPERATION
The CQ-1515 (15 amp) and CQ-1520 (20 amp) are rack mount, plug-in models featuring AC line protection and seven power outputs. These three sequence event devices can be used by themselves, activated via remote control or included with a more extensive power sequencing system. In a typical sequencing system the rack mounted CQ is used to control power to the signal source or “front-of-house” equipment before power is applied to amplifiers. In this configuration, the initial CQ in the series is connected by way of eight wire modular phone cable to another CQ device at that or another location. No time delay settings or additional equipment are required. All CQ units will automatically turn on and off in the proper sequence. Note: the CQ-1520 has a 20 amp capacity and requires a NEMA 5/20R AC receptacle for connection of the power cord to the main AC power.
The CQ-1515 and CQ-1520 feature three sequenced duplex receptacles and one unswitched single AC receptacle on the back of the chassis. Each duplex has its own preset turn on and off timing. Because the CQ activates its outlets in three stages it is useful as a stand-alone sequencer. Signal source and processing equipment can be powered by the first sequence stages while amplifiers are powered by the last ones. The CQ can be triggered by the switch on the front of the unit, by a remote contact closure or by a Juice Goose RC5 accessory.
CONTROL LINE CONNECTION
All CQ products can be easily controlled by way of 8 wire, RJ-45 cable. (Consult the CQ Series Owners Manual before assembling the cable.) Each CQ has a Sequence Signal Input and Output connector on the chassis. This communication link allows any CQ device to be installed at any stage in a power sequencing system. Sequence timing is controlled by a nominal 8 VDC “Outputs Active” circuit between the units which is regenerated with each CQ module. There is no limit to the number of CQ devices that can be connected and no practical distance limit between them.
The system can be activated with the sequence control switch on the CQ device itself or a Juice Goose RC5 control accessory. The sequence process can also be initiated with a latching contact closure, enabling use of a custom mounted single pole switch, a relay or processor based controllers from Crestron, AMX or other manufacturers.
CONTROLS AND MONITORS
The CQ-1515 and CQ-1520 feature a two position switch on the front of the chassis. This switch is active only if there is no control cable on the Sequence Signal Input connector. When active, this switch causes the unit to turn outlets on or off in sequence and to control the sequencing of any unit connected to the Sequence Signal Output connector. A Manual Override switch allows the CQ to be manually operated, overriding the control circuit in the unlikely event of a fault or failure.
Lights on the front of the chassis allow monitoring of the unit operation. The Processor light will blink to indicate the control processor on the unit is functioning. The POD lights are illuminated as a result of contact closure by the CQ relays, indicating that actual relay closure has occurred.
POWER PROTECTION
The CQ-1515 and CQ-1520 feature a multistage AC line filter to reduce high frequency interference and a triple surge protection matrix across hot, neutral and ground power leads.
DETAIL SPECIFICATIONS
Chassis: Tour Class 16 gauge steel with 11 gauge rack mount brackets
Dimensions: 1.75”H x19”W x 7”D
Weight: 10 lb.
Circuit Breaker (thermal on back of the chassis): CQ-1515 15A: CQ-1520 20A
AC Power Filtration: Multistage Filter (48 DB @ 30 MHz)
AC Surge Protection: Triple surge protection matrix on hot, neutral and ground
Number of Sequence Events: Three Power Input (seven foot power cord): CQ-1515 14/3 SJ with NEMA 5/15P plug, CQ-1520 12/3 SJ with 5/20P (requires a 5/20R receptacle)
Power Output (plus one unswitched NEMA 5/15R on back of the chassis), CQ-1515 six sequenced NEMA 5/15R, CQ-1520 six sequenced NEMA 5/20R
Input Voltage: US standard (120 VAC @ 60 Hz)
Signal Connections: RJ-45, eight wire cable
Monitor Features: Monitor LEDs correlate to processor and relay operation
| Weight | 11.000000 |
|---|---|
| Length | 23 |
| Width | 12 |
| Height | 4 |
| Color | Black |
| Manufacturer | Juice Goose |
| Manufacturer Part Number | CQ1515-RX |
| UPC | 85256000084 2 |
| Size | 15 Amps |
Write Your Own Review